# Bicycle gearing

*474*pages on

this wiki

This article needs additional citations for verification.Please help improve this article by adding reliable references. Unsourced material may be challenged and removed. (October 2009) </td>
</tr> </table>A bicycle Multi-speed bicycles allow selection of the appropriate gear ratio for optimum efficiency or comfort, and to suit the circumstances, e.g. it may be comfortable to use one gear when cycling downhill, another when cycling on a flat road, and yet another when cycling uphill. The set of all possible gear ratios on a bicycle is known as the 'gear range'. On a bicycle, power is usually transmitted from the rider's legs to the rear wheel via the pedals and crankset, and then either a chain, belt, shaft, or rarely some other power transmission technology. A cyclist's legs produce power optimally within a narrow pedalling speed range. Gearing is optimized to use this narrow range as best as possible. As in other types of transmissions, the gear ratio is closely related to the mechanical advantage of the drivetrain of the bicycle. On single-speed bicycles and multi-speed bicycles using derailleur gears, the gear ratio is the ratio of the number of teeth on the chainring of the crankset to the rear cog or sprocket, or the ratio of bevel gears on a shaft-driven bicycle. In the case of a derailleur-equipped bicycle, this sprocket is one of several composing the cogset. On hub gears, the ratio is determined by the internal planetary gears within the hub. For a bicycle to travel at the same speed, set to a lower gear (larger mechanical advantage) it will require the rider to pedal at a faster cadence, but with less force. Conversely, a higher gear (smaller mechanical advantage) provides a higher speed for a given cadence, but requires the driver to exert greater force. Different cyclists may have different preferences for cadence and pedaling force. Prolonged exertion of too much force in too high a gear at too low a cadence can increase the chance of knee damage; extremely high cadence and little force maintained at too a low gear also is not advised. ## General considerationsEditThe gearing supplied by the manufacturer on a new bicycle is selected to be useful to the majority of people. Some cyclists choose to fine-tune the gearing to better suit their strength, level of fitness, and expected usage. When buying from specialist cycle shops, it may be less expensive to get the gears altered before delivery rather than at some later date. Modern crankset chainrings can be swapped out, as can cogsets. ## Relative gearingEditAs far as a cyclist's legs are concerned, when changing gears, the relative difference between two gears is more important than the absolute difference between gears. This relative change, from a lower gear to a higher gear, is normally expressed as a percentage. This measure is independent of what system is used to measure the gears. Cycling tends to feel more comfortable if nearly all gear changes have more or less the same percentage difference; a larger percentage difference may be acceptable for lower gears where the absolute difference is not too large. Thus, the absolute gear ratios should be in logarithmic progression; for example 24-35-51 / 34-28-23-19-16-13-11 has a nearly logarithmic progression in steps the same size as the oldest 3-speed planetary hubs, many duplicates, and a very wide range. Modern derailers can handle such combinations. Racing cyclists often have close-range gears with a difference of around 7%. Many general-purpose gears have a difference of around 15%. Differences of 25% or more require a very substantial change in cadence and often feel excessive. A step of 7% corresponds to a 1-tooth change from a 14-tooth cog to a 15-tooth cog, while a step of 15% corresponds to a 2-tooth change from a 13-tooth cog to a 15-tooth cog. By contrast, car engines deliver power over a much larger range of speeds than do cyclists' legs, so relative differences of 30% or more are common for car gearboxes. ## Usable gearsEditNote that with derailleur gears the advertised number of gears may be somewhat misleading. For example, a combination of 3 chainrings and an 8-cog cassette does not result in 24 usable gears. Instead it provides 3 overlapping ranges of 7, 8, and 7 gears (the extremes big-big and little-little should not be used - diagonal chain angles reduce efficiency and cause excessive chain wear). Due to the overlap, there may well be some duplicates or near-duplicates, so that there might only be 16 or 18 distinct gears. It may not be feasible to use these distinct gears in strict low-high sequence anyway due to the complicated shifting patterns involved (e.g. simultaneous double or triple shift on the rear derailleur and a single shift on the front derailleur). In the worst case there could be only 10 distinct gears, if the percentage step between chainrings is the same as the step between cogs. In such a worst case, if the most popular gear is in the middle of the range, the duplication may result in a gear set with a very long useful life, which may be an advantage. While long steep hills and heavy loads may indicate lower gearing, extremely low gears may not allow the rider to maintain the minimum speed necessary to balance a single-track vehicle. ## TechnologyEditThe overlapping ranges with derailleur gears mean that 24 or 27 speed derailleur gears may only have the same total gear range (about 5:1) as a (much more expensive) Rohloff 14-speed hub gear. Internal hub geared bikes typically have a more restricted gear range than comparable derailleur-equipped bikes, and have fewer ratios within that range. On the other hand, a driveshaft system allows greater ground clearance, and the driveshaft and gearing are enclosed, which protects moving parts from the elements. Moreover, there is no danger of clothing or fingers being drawn into the chain and sprockets. ## HistoryEditEarly bicycles and their predecessors were directly driven by the feet. The penny-farthing used a large driven front wheel to increase the top speed, the distance covered per revolution depending only on the wheel size. The safety bicycle introduced driving the rear wheel via a chain, allowing faster travel on a smaller wheel and introducing the concept of bicycle gearing. Later improvements included the freewheel and shifter. Some bicycles have used a double-sided rear wheel, with different-sized sprockets on each side. To change gears, the rider would stop and dismount, remove the rear wheel and reinstall it in the reverse direction. Derailleur systems were first developed in the late 19th century, but the modern cable-operated parallelogram derailleur was invented in the 1950s. ## TypesEdit## External (derailleur)EditMain article: Derailleur gears
## Internal (hub)EditMain article: Hub gear
## Fixed gearEditFixed-gear track racing bikes can achieve transmission efficiencies of over 99% (nearly all the energy put in at the pedals ends up at the wheel). Biomechanical factors however determine that a human can deliver maximum power only over a narrow range of crank rotational speed or ## Internal and external combinedEditIt is sometimes possible to combine a hub gear with deraileur gears, but care is needed when selecting the rear cassette to avoid duplicate gear ratios. A commercially available example of such combined gears is the Brompton folding bicycle which uses a 3-speed hub gear (roughly a 30% difference between gears) in combination with a 2-speed deraileur gear (roughly a 15% difference) to give 6 distinct gears. This is an example of half-step gearing, where one set of gears has an inter-gear step half of that on the other set of gears. Some Brompton suppliers offer a 2-speed chain ring 'Mountain Drive' as well, which results in 12 distinct gears with a range exceeding 5:1. However, the change from 6th to 7th gear involves changing all three sets of gears simultaneously. Another common example is the SRAM DualDrive system, which uses a standard 8 or 9-speed cassette mounted on a three-speed internally-geared hub, offering a similar gear range as a bicycle with a cassette and triple chainwheels. ## OthersEditThere have been, and still are, drivetrains that are quite different from those above: - Shaft-driven bicycles are chainless bicycles that use a driveshaft instead of a chain to transmit power from the pedals to the wheel. Shaft drives were introduced over a century ago, but were mostly supplanted by chain-driven bicycles due to the gear ranges possible with sprockets and derailleurs. Recently, due to advancements in internal gear technology, a small number of modern shaft-driven bicycles have been introduced.
- Retro-Direct drivetrains used on some early 20th century bicycles have been resurrected by bicycle hobbyists. These have two gears but no gear lever; the operator simply pedals forward for one gear and backward for the other.
- In recent years, Steve Christini and Mike Dunn introduced a two-wheel drive option. Their AWD system, aimed at mountain bikers, comprises an adapted differential that sends power to the front wheel once the rear begins to slip.
- Automatic transmissions have been demonstrated and marketed for both derailleur and hub gear mechanisms, often accompanied by a warning to disengage auto-shifting if standing on the pedals. These have met with limited market success.
- Continuously variable transmissions are a relatively new development in bicycles (though not a new idea). Mechanisms like the NuVinci gearing system use a ball connected to two disks by static friction - changing the point of contact changes the gear ratio.
## Measuring gearsEditWith a derailleur-based multi-speed bicycle, the gears can be denoted by the number of teeth on the front chainring and rear sprocket, for example the highest gear on a racing bicycle might be 53x11. For a road-racing cyclist, this is useful because of the standard size of the wheel. However, this measure is limited because it does not specify other aspects of the system. With a hub gear, gear ratios are given directly. Gear inches and meters of development of a gear combination are defined: - Gear inches =
**Diameter**of drive wheel in inches × number of teeth in front chainring / number of teeth in rear cog. - Metres of development =
**Circumference**of drive wheel in metres × number of teeth in front chainring / number of teeth in rear cog.
Metres of development corresponds to the distance (in metres) traveled by the bicycle for one rotation of the pedals. Gear inches has no current physical significance; it corresponds to the diameter of the main wheel of an old-fashioned penny-farthing bicycle with equivalent gearing. To convert from gear inches to metres of development, multiply by 0.08 (more exactly: 0.0798, or precisely: ). The table below shows distance traveled in metres per pedal revolution for a typical sprocket configuration on a 27 inch bicycle. Note that the two highest gears use the large front sprocket, the two lowest gears use the small front sprocket, while for all other gears, it is necessary to shift both front and rear sprockets to access the next higher or lower gear ratio. Some gears, indicated by asterisks (*) may have less favorable chain geometry due to crossover between inner and outer sprockets.
The following table compares gear inches, metres of development, and gain ratio for 170 mm cranks and 700c wheels (diameter 70 cm). Speeds for several cadences in revolutions per minute are also given.
Only those who want to go really fast will need a gear much above 100, though gears as high as 250 have been reported for specialist racing. Cyclists who are fit and strong will find that a low gear of around 40 -50 gear-inches is quite adequate for almost all on-road use. Other cyclists may prefer a somewhat lower gear, perhaps around 20 or 30. The lowest feasible non-specialist gear (as of 2005) is around 15. Tricycles can be bought with gears as low as 8, but such low gears are not really suitable for bicycles due to the problems of balancing at very slow speeds. As a person ages, their necessary low gear may change. Suppose a cyclist at age 40 regularly commutes by bicycle 11 miles each way without doing any other cycling or exercise. He/she might need a low gear of 45 for the 58-mile London to Brighton charity bike ride, with no need to stand on the pedals even over Ditchling Beacon. Twenty years later the same cyclist (then commuting only 5 miles each way) might need a low gear of 27 for the ride. Another five years later the same cyclist (then commuting 7 miles each way) might feel happier with a low gear of 19 for the ride. Several gear ratio calculators are linked below. Such calculators are more useful if they show the percentage difference between gears as well as the nominal gear ratios. These calculators require the number of teeth on each gear wheel on the bicycle and the diameter of the back wheel. Standard road wheels, labeled 700c are 70 cm in diameter with the tire; the smaller 650c wheels are 65 cm in diameter. Mountain, cruiser, and most other types of wheel are 26 inches with tire. For gain ratios they also need to know the length of the pedal cranks in millimetres (crank lengths are normally some multiple of 2.5 mm). If the bicycle has an enclosed gear system (hub or bottom bracket), then details of these gears are also needed (make and model is enough for some calculators). ## Some examplesEditThe following gear ratios were calculated using a 700c rear wheel. Similar ratios can be obtained for any size wheel by adjusting the size of the chainring and/or the rear sprocket. It is possible to get almost any combination of chainwheel sizes and cog sizes, but it is much cheaper to use standard combinations. ## Short local ridesEditScenario: short distances (up to 5 miles/8 km), fairly flat. - Use a single speed bicycle with a gear of around 60.
- Desired gears: low around 50, high around 70.
- Use Sturmey-Archer KS close-ratio 3-speed hub to get gears of 53, 59, 67.
- Use a Sturmey-Archer FC close-ratio 4-speed hub to get gears of 49, 58, 65, 71.
- Use a Sturmey-Archer AW wide-ratio 3-speed hub to get gears of 45, 60, 80.
- Desired gears: low around 40, high around 90, step around 15%.
- Use single chain ring and a 7-cog (14-32) cassette to get gears of 41, 46, 54, 62, 72, 81, 93.
- Use a 7-cog (13-30) cassette to get gears of 40, 46, 52, 59, 70, 79, 91.
- Use a Shimano Nexus 7-speed hub to get gears of 38, 44, 50, 59, 68, 78, 92.
## Regular commutingEditScenario: between 5 and 10 miles (8 to 16 km) each way on working days, plus occasional longer trips. - Desired gears: low around 40, high around 90, step around 15%.
- Use the same 7-speed gears as for the last option re short local rides above.
- Desired gears: low around 40, high around 100, step around 15%.
- Use single chain ring and a 7-cog (12-28) cassette to get gears of 42, 50, 57, 66, 74, 85, 99.
- Use an 8-cog (11-28) cassette to get gears of 41, 47, 54, 63, 71, 81, 95, 103.
- Desired gears: low around 30, high around 100, step around 15%.
- Use single chain ring and an 8-cog (11-34) Megarange cassette to get gears of 32, 42, 47, 54, 64, 72, 83, 98. Note that with this cassette there is a big jump (31%) from 32 to 42.
- Or eliminate the big jump by using a 9-cog (11-34) cassette to get gears of 32, 36, 42, 47, 54, 64, 72, 83, 98.
- Or use two chainrings (30,40) with an 8-cog (11-28) cassette to get high-range gears 45, 51, 60, 68, 77, 90, 98 and low-range gears 29, 34, 39, 45, 51, 58, 68. Note that there are 4 duplicate gears, so there are really only 10 distinct gears.
- Desired gears: low around 30, high around 100, step around 8%.
- Use two chainrings (39,42) with an 8-cog (12-32) cassette to get high-range gears 41, 47, 54, 63, 71, 81, 95 and low-range gears 33, 38, 44, 50, 59, 66, 75. Note that this combination is what is called 'half-step gearing' - the percentage step between chainrings is about half the step between cogs. The two ranges are interlaced to avoid duplicates (there are 14 distinct gears), but achieving an 8% difference requires simultaneous front and rear derailleur changes on every other gear change.
- Or use 3 chainrings (28,38,48) with a 9-cog (13-25) close-range cassette to get high-range gears 56, 62, 68, 76, 81, 86, 93, 100 and mid-range gears 41, 45, 49, 54, 60, 64, 68, 73, 79 and low-range gears 30, 33, 36, 40, 45, 47, 50, 54. There are 20 distinct gears out of a nominal 27, but they are not really usable in sequence.
- Desired gears: low around 25, high around 100, step around 15%.
- Use 3 chainrings (28,38,48) with an 8-cog (11-34) Megarange cassette to get high-range gears 50, 57, 65, 77, 87, 100, 119, and mid-range gears 30, 40, 45, 52, 61, 69, 79, 94 and low-range gears 22, 29, 33, 38, 45, 51, 59. This combination has an 'overdrive' of 119 at the top for those strong enough to use it.
- Or use 3 chainrings (24,34,42) with an 8-cog Megarange (11-34) cassette to get high-range gears 44, 49, 57, 67, 76, 87, 103 and mid-range gears 27, 35, 40, 46, 54, 61, 71, 84 and low-range gears 19, 25, 28, 32, 38, 43, 50. This combination has a "crawler gear" or "granny gear" of 19 at the bottom for tackling those really steep hills.
## TouringEditScenario: Longer trips of 30 to 60 miles (50 to 95 km) per day, heavily laden. - Desired gears: low around 20, high around 100, with plenty of low gears.
- Use single chainring with Rohloff 14-speed hub (13.5% difference throughout) to get gears: 19, 22, 25, 28, 32, 36, 41, 47, 53, 61, 69, 78, 89, 101.
- Or use 3 chainrings (22,32,44) with an 8-cog (12-32) cassette to get high-range gears 42, 50, 57, 66, 74, 85, 99 and mid-range gears 27, 31, 36, 41, 48, 54, 62, 72 and low-range gears 19, 21, 25, 28, 33, 37, 42. There is a lot of overlap between the ranges, so this combination only has 13 distinct gears out of a nominal 24!
- Or use three chainrings (22,39,42) with an 8-cog (12-32) cassette to get high-range gears 41, 47, 54, 63, 71, 81, 95 and mid-range gears 33, 38, 44, 50, 59, 66, 75, 88 and low-range gears 19, 21, 25, 28, 33, 37, 42. This combination uses half-step gearing on the high and middle ranges in combination with a much larger jump between the middle ring and the smallest (granny) ring to provide a total of 19 distinct gears, and is known as "half-step plus granny" gearing.
^{[2]}
## RacingEditScenario: Speed is important, strength is assumed. Desired gears: low around 45, high around 125, step around 8%. A modern racing bicycle is often equipped with a double-chainring crankset at the front and a 9-speed or 10-speed cassette at the back. Since wheel size is standardized, the gearing system is often described by stating the number of teeth in the chainrings and cogs. For example, the front chainring gearing is denoted "53/39", meaning that it has 53- and 39-tooth chainrings on the crankset. The rear cassette is denoted by its smallest and its largest. For example, a "12-25" means that the smallest has 12 teeth, and the largest has 25 teeth. Nowadays 9- and 10-speed cassettes are commonplace, which make the choice of intermediate gears less important than when there were only 5 cogs available in a cassette. These cassettes typically have a 7% step on the top 6 or 7 gears, and an 11% step on the lower gears. Except in special circumstances, most professionals use a combination of a 53/39 front gearing. Some sprinters like to use a larger chainring at the front, up to 54t or 55t. In some races involving steep climbs, some professionals opt for a triple chainring at the front to accommodate a smaller gear. Recent popularity of the compact drivetrain allows the use of smaller chainrings at the front, usually a 50/34 or 50/36 combination. This allows the use of a double-chainring drivetrain and having the lower gearing needed for the climbs. ## Off-roadEdit"Alpine gearing" of approximately 15% step is preferred. Typically cross country mountain bikes will be fitted with a triple crankset, using 22, 32 and 44 tooth chainrings. The rear cassette is usually an 11 to 32. For downhill specific bikes, road type cassettes may be fitted to provide smaller steps between gears, along with cranksets fitted with one or two drive rings and a bash ring, which takes the place of the largest chainring, and is simply a reinforced, toothless ring, designed to protect the smaller two chainrings from impact via logs, rocks, deep ruts, crashes, etc. Template:Sectstub ## See alsoEdit- Bicycle
- Cogset
- Crankset
- Derailleur gears
- Drivetrain
- Hub gear
- NuVinci
- Recumbent bicycle
- Rohloff Speedhub 14-speed hub gear
## ReferencesEdit- ↑ Whitt, Frank R.; David G. Wilson (1982).
*Bicycling Science*(Second edition ed.). Massachusetts Institute of Technology. pp. 277–300. ISBN 0-262-23111-5. - ↑ Template:Cite web
## External linksEdit- Cycling glossary, links to articles
- Detailed discussion on gearing
- Calculate your gear ratios
- Calculate your gear ratios and shifting pattern
- Calculate speed based on gearing and cadence
- Gearing 101
- Cadence training
- Derailleur Gears: A practical guide to their use and operation.
Template:Gearsde:Gangschaltung es:Transmisión de bicicleta he:הילוכים באופניים fr:Régler les vitesses d'un vélo ms:Gear basikal ja:変速機 (自転車) |